How To Read Degrees On A Plat Map

This reads north, 63 degrees east. surveyors can mark the compass degree system as precisely as they want. For inches, divide the large number on the map scale (i.e.

Printable 360 Degree Wheel with Compass Rose Compass

For our 1:9,000 map example, the millimeter divide by number equals 1.8 (1 millimeter = 1.8 poles).

How to read degrees on a plat map. A map’s scale provides a ratio of map distance to actual distance. To read the coordinates of any location, start with the number of degrees on the latitude line, and clarify whether it is in the northern or southern hemisphere. The corners of your plat map will have the book and page number.

Each degree is then broken down into 60 minutes. Site plan is a drawing that is a bird’s Now click on the other parcel corners that interest you to see those coordinates.

A survey bearing indicates the quadrant in which it exists and the number of degrees into that quadrant measured from zero. The angle is calculated as degrees+minutes/60+seconds/3600. Deedpoint is a list of tuples, while 'd' is a tuple.

So, to make our heading work, we need to add 36 to 180, giving us 216 degrees. The scale will differ from map to map, but will typically be presented as a number ratio, like “1 : You read an old plat from the 40's with metes and bounds rounded to the nearest degree.

This will give you an idea of just how far you have to go. Sometimes a client will note that measured bearings and distances vary somewhat from the recorded measurements shown within the deed or on the plat. The elements of a list or a tuple are indexed by a number starting with zero.

Thence n 89 degrees 54’41” w, 314.69 feet to the east line of a 20 foot easement; Thence run n 0 degrees. Subdivision plats must be completed by a licensed surveyor and meet the survey plat recording requirements of 27 v.s.a.

Directly to your right (east) would be 90 degrees east of north. The angle can be stated as a certain number of degrees (°), followed by an additional number of minutes ('), followed by a certain number of seconds (). Our compass puts north at 0 degrees.

The distances are usually indicated in u.s. If you turned around you would be facing south and would be 180 degrees south of north. The plat is actually based on a previous plat drawn in 1850 so you're another 2 degrees off.

Learning to read a land survey map is not only for surveyors. To better understand this concept, imagine that you are facing north. I prefer the decimal format.

This is then converted to cartesian degrees by the nested if/then. Consider which format you want to use. The scale of your plat map will be in the map’s legend.

The scale will be the ratio between the distance on the map and the distance of the actual property. This can be read more descriptively as north 66 degrees 0 minutes and 0 seconds for a distance of 1245.01 feet. 4 degrees of error down one side of your parcel equates to about a 460' error in where you think the property corner should be.

How to read a land survey map. These are usually drawn and then each line is annotated with bearing and distance. As you continue to turn you would face west, located 90 degrees west of north.

Since south from there would be 180 degrees, 36 degrees does not make much sense. The earth is nearly 25,000 miles around, so once divided into 360 degrees, it means each degree is about 69 miles wide. For our 1:9,000 map example, the inches divide by number equals 45.5.

Survey plats can also be read in reverse. N42w, or 42 degrees west of north; An example of bearing and distance might be n 66° 0′ 0″ e 1245.01′.

If your map shows seconds, find the second closest to where each line intersects the latitude or longitude scale at the edge of the map. A site plan package can include: A plat is a map of a land area, usually on the scale of a neighborhood or county township, and a plot is a piece of land used for a single purpose (such as a park or a home).

Thence continue s 0 degrees 03’08” e, 409.67 feet; Click on the remaining corners. You miss figure the declination from the magnetic bearing shown on the plat by 2 degrees.

For millimeters, divide the large number on the map scale (i.e. Information relative to roads, lighting, landscaping, natural features, access, soil erosion control, and stormwater management. So if 'q = deedpoints[0]', then 'q[0] = n' and 'q[5] = 1401.09'.

Land survey maps are used to measure everything from. Use a ruler to get the most accurate reading of your plat map. 100,000.” this ratio simply means that 1 unit of distance on the map is equal to 100,000 units in real life.

You probably remember from school that a circle is 360 degrees, a degree is 60 minutes and a minute is 60 seconds. Read the compass degree system by starting with a specific point on the compass (north, east, south or west), and then reading the number of the degrees to the next point on the compass. An example heading might be n63e.

For example, if your latitude line falls about 5″ above the 32°20′n line, your point is at a latitude of approximately 32°20′5″n. The second format is degrees, minutes and seconds:

How to Use SPSSCronbach's Alpha Reliability Test in 2020